Settings - Sensor

TEMPERATURE
 
Hysteresis
For more information, read an article on hysteresis.
Low threshold
Lower limit for normal Device state. If temperature drops below this value, Device will be in alarm.
High threshold
Upper limit for normal Device state. If temperature rises above this value, Device will be in alarm.
Measurement temperature offset
Value (can be negative) added to the measured temperature to compensate for conditions that do not meet Supracontrol recommendations.
Enable alarm delay
Alarm delay (suppression) option prevents unwanted alarms resulting from value spikes. When checked, the Device must be in alarm continuously for the set amount of time (in minutes) before the Device signals an alarm. If the measured value returns within thresholds in the set time period, there will be no alarm and the delay timer will be reset.
Delay (in minutes)
Set the amount of time the Device needs to be in alarm before sending notifications.
Enable repeat
Repeat feature ensures you do not forget that the Device is in alarm. As long as the Device is in alarm, it will periodically resend notifications to remind you.
Repeat interval
How often the Device resends notifications.
Measurement unit
Choose your preferred temperature measurement unit between degrees Celsius or Fahrenheit.
 
 
HUMIDITY
 
Hysteresis
For more information, read an article on hysteresis.
Low threshold
Lower limit for normal Device state. If humidity drops below this value, Device will be in alarm.
High threshold
Upper limit for normal Device state. If humidity rises above this value, Device will be in alarm.
Enable alarm delay
Alarm delay (suppression) option prevents unwanted alarms resulting from value spikes. When checked, the Device must be in alarm continuously for the set amount of time (in minutes) before the Device signals an alarm. If the measured value returns within thresholds in the set time period, there will be no alarm and the delay timer will be reset.
Delay (in minutes)
Set the amount of time the Device needs to be in alarm before sending notifications.
Enable repeat
Repeat feature ensures you do not forget that the Device is in alarm. As long as the Device is in alarm, it will periodically resend notifications to remind you.
Repeat interval
How often the Device resends notifications.
 
 
DIGITAL INPUTS
 
Input names
Rename your inputs in order to distinguish them more easily. (Currently limited to 15 characters)
Enable alarm delay
Alarm delay (suppression) option prevents unwanted alarms resulting from short-term Input ON states. When checked, the Device must be in alarm continuously for the set amount of time (in minutes) before the Device signals an alarm. If the Input reverts to OFF state in the set time period, there will be no alarm and the delay timer will be reset.
Delay (in minutes)
Set the amount of time the Device needs to be in alarm before sending notifications.
On value
Value to be displayed when the input is in ON state, sending a signal to the Device.
Off value
Value to be displayed when the input is in OFF state, not sending a signal to the Device.
Invert state
Switches the logic of input states. By default, when an input is sending a signal, it is considered to be ON; when it is not, it is considered OFF. When invert state option is enabled, the input sending a signal will be considered OFF, and the input not sending a signal will be considered ON.
 
 
 
DIGITAL OUTPUTS
 
Output names
Rename your inputs in order to distinguish them more easily. (Currently limited to 15 characters)
Enable alarm delay
Alarm delay (suppression) option prevents unwanted alarms resulting from short-term Output ON states. When checked, the Device must be in alarm continuously for the set amount of time (in minutes) before the Device signals an alarm. If the Output reverts to OFF state in the set time period, there will be no alarm and the delay timer will be reset.
Delay (in minutes)
Set the amount of time the Device needs to be in alarm before sending notifications.
On value
Value to be displayed when the input is in ON state, sending a signal to the Device.
Off value
Value to be displayed when the input is in OFF state, not sending a signal to the Device.
Initial state
Choose the default state that Relay Output is set to upon Device power-up
On - Relay is initially set to ON state when the Device is powered-up
Off - Relay is initially set to OFF state when the Device is powered-up
Unchanged - Relay state is initially the same as it was at the moment of last power-down.
 
Have more questions? Submit a request